- MORE 產品快速導航
SLK801壓力變送器 稱重傳感器是在現實生活中應用最多的一種傳感器,很多尋常百姓家里都可以看見,今天我們來說說工業上應用的產品。稱重傳感器本身具有結構牢固、經久耐用的優點，但是在使用安裝過程當中如果不注意的話，也會影響它性能的發揮。
對于小計量的傳感器，應該避免它受到?jīng)_擊，這會影響到它今后測量值的準確性。大計量的產品本身重要比較重，搬運的時候最好使用專用的搬運工具，落到地面的時候要減緩速度，避免震動對它里面器件造成損壞，同時安裝基座要水平放置，底部要清掃干凈，不能有雜物存在。任何稱重傳感器在使用過程中需避免超載測量，這會導致彈性體形變不可恢復，造成永久損壞。
傳感器在水平調整過程中，最好使用水平儀，使得安裝的傳感器在統一水平面上，保證其所受負荷的一致性。
傳感器要采用螺栓固定，保證一定的緊固力矩，長時間使用不會松動。
傳感器的安裝位置盡量遠離大功率設備，因為它本身的輸出信號就比較弱，通常為毫伏級，極易受到干擾。在這種情況下，將傳感器罩起來，輸出信號選擇帶屏蔽的雙絞線纜傳送，其性能會好一點。線纜鋪設的時候還要避免與動力電纜平行鋪設。必須平行放置的時候，它們之間的距離必須大于50厘米，同時信號電纜要用專業套管進行保護，其屏蔽線纜必須單測接地且不能和電源線共地。
安裝在室外的稱重傳感器要注意防雨防輻射。
對于已投入時間很長的傳感器，可以用加小負載的方式，檢查它的輸出是否有變動，它的運動部件有可能雜物的影響，導致其輸出精度降低。
Load cell is the most widely used in real life of a sensor, a lot of ordinary people at home can see, today we are concerned that industrial application of the product. Structure of the load cell itself has a solid, long-lasting benefits, but in using the installation process if not careful, it will also affect the performance of the play.
For small measurement sensor, it should be avoided under attack, this will affect its future measurement accuracy. Large measure the product itself is more important important, handling time is best to use a dedicated removal tool, to reach the ground time to slow down, shake it inside to avoid damage to the device, while the base to be installed horizontally, the bottom should be cleaned , can not have debris exist. Any load cell in the course of measuring the need to avoid overloading, which causes the elastic body becomes irreversible, causing permanent damage.
Sensor in the horizontal adjustment process, it is best to use the level meter, making the installation of sensors in a unified horizontal plane, to ensure the consistency of the load they suffered.
Sensor bolt to be used to ensure a certain degree of tightening torque, prolonged use will not become loose.
Sensor is installed as far away from high-power devices, because its own output signal is relatively weak, typically millivolts, vulnerable to interference. In this case, the sensor covers up, choose the output signal transmission with shielded twisted pair cable, its performance will be better. Even when laying cables and power cables to avoid parallel laying. Must be placed in parallel, when the distance between them must be greater than 50 cm, while the signal cable to use professional tube to protect the cable shield must be grounded and not a single measure of ground and power lines.
Load cell installed in the outdoor rain to pay attention to radiation.
For a long time has been put into the sensor, plus a small load can be a way to check whether there are changes in its output, its moving parts may be debris impact, resulting in lower output accuracy.